-
1 conductor area
сечение жилы кабеля
-
[Интент]
Рис. ABBCable area 2.5 - 6 mm2
[ABB]
Сечение жилы кабеля 2,5 - 6 мм2
[Перевод Интент]
Параллельные тексты EN-RU
Unless otherwise stated in specifications, the following cable cross sections are recommended for auxiliary wirings.
[Schneider Electric]При отсутствии в технических требованиях других указаний для выбора сечения жил кабелей вспомогательных цепей, следует пользоваться приведенными ниже рекомендациями.
[Перевод Интент]
Тематики
- кабели, провода...
- клемма электротехническая
EN
Англо-русский словарь нормативно-технической терминологии > conductor area
-
2 connectable conductor area
номинальное сечение зажима, мм2
Значение сечения присоединяемого проводника, указанное изготовителем
[ ГОСТ Р 50030.7.1-2000]Тематики
- вывод, зажим электрический
- клемма электротехническая
EN
Англо-русский словарь нормативно-технической терминологии > connectable conductor area
-
3 conductor cross section
сечение проводника
-
[Интент]Выбор сечений проводников по нагреву
Если сечение проводника, определенное по этим условиям, получается меньше сечения, требуемого по другим условиям (термическая и электродинамическая стойкость при токах КЗ, потери и отклонения напряжения, механическая прочность, защита от перегрузки), то должно приниматься наибольшее сечение, требуемое этими условиями.
Сечение проводников основной системы уравнивания потенциалов должно быть не менее половины наибольшего сечения защитного проводника электроустановки, если сечение проводника уравнивания потенциалов при этом не превышает 25 мм2 по меди или равноценное ему из других материалов.
[ПУЭ]В одно- или трехфазных сетях сечение нулевого рабочего проводника и PEN-проводника должно быть равным сечению фазного проводника при его сечении 16 мм2 и ниже для проводников с медной жилой и 25 мм2 и ниже - для проводников с алюминиевой жилой. При больших сечениях фазных проводников допускается снижение сечения нулевого рабочего проводника при условии, что:
- ожидаемый максимальный рабочий ток в нулевом проводнике не превышает его длительно допустимый ток;
- нулевой защитный проводник имеет защиту от сверхтока.
[ ГОСТ Р 50571. 15-97 ( МЭК 364-5-52-93)]Недопустимые, нерекомендуемые
Тематики
- кабели, провода...
- электропроводка, электромонтаж
- электроустановки
EN
Англо-русский словарь нормативно-технической терминологии > conductor cross section
-
4 conductor cross-sectional area
Кабельные производство: сечение токопроводящей жилыУниверсальный англо-русский словарь > conductor cross-sectional area
-
5 conductor cross-sectional area
English-Russian dictionary of terminology cable technology > conductor cross-sectional area
-
6 cable area
сечение жилы кабеля
-
[Интент]
Рис. ABBCable area 2.5 - 6 mm2
[ABB]
Сечение жилы кабеля 2,5 - 6 мм2
[Перевод Интент]
Параллельные тексты EN-RU
Unless otherwise stated in specifications, the following cable cross sections are recommended for auxiliary wirings.
[Schneider Electric]При отсутствии в технических требованиях других указаний для выбора сечения жил кабелей вспомогательных цепей, следует пользоваться приведенными ниже рекомендациями.
[Перевод Интент]
Тематики
- кабели, провода...
- клемма электротехническая
EN
Англо-русский словарь нормативно-технической терминологии > cable area
-
7 cross-sectional area of the conductor
сечение проводника
-
[Интент]Выбор сечений проводников по нагреву
Если сечение проводника, определенное по этим условиям, получается меньше сечения, требуемого по другим условиям (термическая и электродинамическая стойкость при токах КЗ, потери и отклонения напряжения, механическая прочность, защита от перегрузки), то должно приниматься наибольшее сечение, требуемое этими условиями.
Сечение проводников основной системы уравнивания потенциалов должно быть не менее половины наибольшего сечения защитного проводника электроустановки, если сечение проводника уравнивания потенциалов при этом не превышает 25 мм2 по меди или равноценное ему из других материалов.
[ПУЭ]В одно- или трехфазных сетях сечение нулевого рабочего проводника и PEN-проводника должно быть равным сечению фазного проводника при его сечении 16 мм2 и ниже для проводников с медной жилой и 25 мм2 и ниже - для проводников с алюминиевой жилой. При больших сечениях фазных проводников допускается снижение сечения нулевого рабочего проводника при условии, что:
- ожидаемый максимальный рабочий ток в нулевом проводнике не превышает его длительно допустимый ток;
- нулевой защитный проводник имеет защиту от сверхтока.
[ ГОСТ Р 50571. 15-97 ( МЭК 364-5-52-93)]Недопустимые, нерекомендуемые
Тематики
- кабели, провода...
- электропроводка, электромонтаж
- электроустановки
EN
Англо-русский словарь нормативно-технической терминологии > cross-sectional area of the conductor
-
8 size conductor
определять сечение проводника
-
[Интент]Параллельные тексты EN-RU
Conductors must always be sized to withstand the nominal current.
Сечение проводников должно обеспечивать пропускание номинального тока.
[Перевод Интент]
Тематики
- кабели, провода...
EN
сечение проводника
-
[Интент]Выбор сечений проводников по нагреву
Если сечение проводника, определенное по этим условиям, получается меньше сечения, требуемого по другим условиям (термическая и электродинамическая стойкость при токах КЗ, потери и отклонения напряжения, механическая прочность, защита от перегрузки), то должно приниматься наибольшее сечение, требуемое этими условиями.
Сечение проводников основной системы уравнивания потенциалов должно быть не менее половины наибольшего сечения защитного проводника электроустановки, если сечение проводника уравнивания потенциалов при этом не превышает 25 мм2 по меди или равноценное ему из других материалов.
[ПУЭ]В одно- или трехфазных сетях сечение нулевого рабочего проводника и PEN-проводника должно быть равным сечению фазного проводника при его сечении 16 мм2 и ниже для проводников с медной жилой и 25 мм2 и ниже - для проводников с алюминиевой жилой. При больших сечениях фазных проводников допускается снижение сечения нулевого рабочего проводника при условии, что:
- ожидаемый максимальный рабочий ток в нулевом проводнике не превышает его длительно допустимый ток;
- нулевой защитный проводник имеет защиту от сверхтока.
[ ГОСТ Р 50571. 15-97 ( МЭК 364-5-52-93)]Недопустимые, нерекомендуемые
Тематики
- кабели, провода...
- электропроводка, электромонтаж
- электроустановки
EN
Англо-русский словарь нормативно-технической терминологии > size conductor
-
9 cable cross section
сечение жилы кабеля
-
[Интент]
Рис. ABBCable area 2.5 - 6 mm2
[ABB]
Сечение жилы кабеля 2,5 - 6 мм2
[Перевод Интент]
Параллельные тексты EN-RU
Unless otherwise stated in specifications, the following cable cross sections are recommended for auxiliary wirings.
[Schneider Electric]При отсутствии в технических требованиях других указаний для выбора сечения жил кабелей вспомогательных цепей, следует пользоваться приведенными ниже рекомендациями.
[Перевод Интент]
Тематики
- кабели, провода...
- клемма электротехническая
EN
Англо-русский словарь нормативно-технической терминологии > cable cross section
-
10 size of the cable
сечение жилы кабеля
-
[Интент]
Рис. ABBCable area 2.5 - 6 mm2
[ABB]
Сечение жилы кабеля 2,5 - 6 мм2
[Перевод Интент]
Параллельные тексты EN-RU
Unless otherwise stated in specifications, the following cable cross sections are recommended for auxiliary wirings.
[Schneider Electric]При отсутствии в технических требованиях других указаний для выбора сечения жил кабелей вспомогательных цепей, следует пользоваться приведенными ниже рекомендациями.
[Перевод Интент]
Тематики
- кабели, провода...
- клемма электротехническая
EN
Англо-русский словарь нормативно-технической терминологии > size of the cable
-
11 terminal capacity
ёмкость выводов
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
номинальное сечение зажима, мм2
Значение сечения присоединяемого проводника, указанное изготовителем
[ ГОСТ Р 50030.7.1-2000]Тематики
- вывод, зажим электрический
- клемма электротехническая
EN
Англо-русский словарь нормативно-технической терминологии > terminal capacity
-
12 capacity of connector
номинальное сечение зажима, мм2
Значение сечения присоединяемого проводника, указанное изготовителем
[ ГОСТ Р 50030.7.1-2000]Тематики
- вывод, зажим электрический
- клемма электротехническая
EN
Англо-русский словарь нормативно-технической терминологии > capacity of connector
-
13 capacité assignée de connexion
допустимое сечение присоединяемых проводников
-
[IEV number 442-06-32]EN
rated connecting capacity
The cross-sectional area of the largest rigid conductor(s) to be connected as stated by the manufacturer of the connecting device
[IEV number 442-06-32]FR
capacité assignée de connexion
Section du(des) plus gros conducteur(s) rigide(s) pouvant être raccordé(s), indiquée par le constructeur du dispositif de connexion
[IEV number 442-06-32]EN
DE
FR
номинальная способность к присоединению
Диапазон и/или число номинальных сечений проводников, на которое рассчитана клемма
[ ГОСТ Р 50030.7.1-2000]EN
rated connecting capacity
range of cross-sections and, if applicable, the number of connectable conductors, for which the terminal block is designed
[IEC 60947-7-1, ed. 3.0 (2009-04)]
rated connecting capacity
cross-sectional area of the largest conductor(s) to be connected as stated by the manufacturer of the installation couple
[IEC 61535, ed. 1.0 (2009-02)]
rated connecting capacity
cross-sectional area of the largest conductors as declared by the manufacturer
[IEC 60670-22, ed. 1.0 (2003-05)]
rated connecting capacity
cross-sectional area of the largest rigid conductor(s) to be connected as stated by the manufacturer of the connecting device. In the case of a connecting device for flexible conductors only, the rated connecting capacity is the cross-sectional area of the largest flexible conductor to be connected
[IEC 60998-1, ed. 2.0 (2002-12)]FR
capacité assignée de raccordement
gamme de sections et, le cas échéant, nombre de conducteurs raccordables, pour lesquels le bloc de jonction est conçu
[IEC 60947-7-1, ed. 3.0 (2009-04)]
capacité assignée de connexion
section du ou des plus grands conducteurs susceptibles d’être connectés comme indiqué par le fabricant du coupleur d’installation
[IEC 61535, ed. 1.0 (2009-02)]
capacité assignée de connexion
section du ou des plus gros conducteurs déclarée par le constructeur
[IEC 60670-22, ed. 1.0 (2003-05)]
capacité de connexion assignée
section du ou des plus gros conducteurs rigides à raccorder, déclarée par le constructeur du dispositif de connexion. Dans le cas d'un dispositif de connexion pour conducteurs flexibles uniquement, la capacité de connexion assignée est la section du plus gros conducteur flexible à raccorder
[IEC 60998-1, ed. 2.0 (2002-12)]Тематики
- вывод, зажим электрический
- изделие электроустановочное
- клемма электротехническая
EN
FR
Франко-русский словарь нормативно-технической терминологии > capacité assignée de connexion
-
14 capacité assignée de raccordement
номинальная способность к присоединению
Диапазон и/или число номинальных сечений проводников, на которое рассчитана клемма
[ ГОСТ Р 50030.7.1-2000]EN
rated connecting capacity
range of cross-sections and, if applicable, the number of connectable conductors, for which the terminal block is designed
[IEC 60947-7-1, ed. 3.0 (2009-04)]
rated connecting capacity
cross-sectional area of the largest conductor(s) to be connected as stated by the manufacturer of the installation couple
[IEC 61535, ed. 1.0 (2009-02)]
rated connecting capacity
cross-sectional area of the largest conductors as declared by the manufacturer
[IEC 60670-22, ed. 1.0 (2003-05)]
rated connecting capacity
cross-sectional area of the largest rigid conductor(s) to be connected as stated by the manufacturer of the connecting device. In the case of a connecting device for flexible conductors only, the rated connecting capacity is the cross-sectional area of the largest flexible conductor to be connected
[IEC 60998-1, ed. 2.0 (2002-12)]FR
capacité assignée de raccordement
gamme de sections et, le cas échéant, nombre de conducteurs raccordables, pour lesquels le bloc de jonction est conçu
[IEC 60947-7-1, ed. 3.0 (2009-04)]
capacité assignée de connexion
section du ou des plus grands conducteurs susceptibles d’être connectés comme indiqué par le fabricant du coupleur d’installation
[IEC 61535, ed. 1.0 (2009-02)]
capacité assignée de connexion
section du ou des plus gros conducteurs déclarée par le constructeur
[IEC 60670-22, ed. 1.0 (2003-05)]
capacité de connexion assignée
section du ou des plus gros conducteurs rigides à raccorder, déclarée par le constructeur du dispositif de connexion. Dans le cas d'un dispositif de connexion pour conducteurs flexibles uniquement, la capacité de connexion assignée est la section du plus gros conducteur flexible à raccorder
[IEC 60998-1, ed. 2.0 (2002-12)]Тематики
- вывод, зажим электрический
- изделие электроустановочное
- клемма электротехническая
EN
FR
Франко-русский словарь нормативно-технической терминологии > capacité assignée de raccordement
-
15 capacité de connexion assignée
номинальная способность к присоединению
Диапазон и/или число номинальных сечений проводников, на которое рассчитана клемма
[ ГОСТ Р 50030.7.1-2000]EN
rated connecting capacity
range of cross-sections and, if applicable, the number of connectable conductors, for which the terminal block is designed
[IEC 60947-7-1, ed. 3.0 (2009-04)]
rated connecting capacity
cross-sectional area of the largest conductor(s) to be connected as stated by the manufacturer of the installation couple
[IEC 61535, ed. 1.0 (2009-02)]
rated connecting capacity
cross-sectional area of the largest conductors as declared by the manufacturer
[IEC 60670-22, ed. 1.0 (2003-05)]
rated connecting capacity
cross-sectional area of the largest rigid conductor(s) to be connected as stated by the manufacturer of the connecting device. In the case of a connecting device for flexible conductors only, the rated connecting capacity is the cross-sectional area of the largest flexible conductor to be connected
[IEC 60998-1, ed. 2.0 (2002-12)]FR
capacité assignée de raccordement
gamme de sections et, le cas échéant, nombre de conducteurs raccordables, pour lesquels le bloc de jonction est conçu
[IEC 60947-7-1, ed. 3.0 (2009-04)]
capacité assignée de connexion
section du ou des plus grands conducteurs susceptibles d’être connectés comme indiqué par le fabricant du coupleur d’installation
[IEC 61535, ed. 1.0 (2009-02)]
capacité assignée de connexion
section du ou des plus gros conducteurs déclarée par le constructeur
[IEC 60670-22, ed. 1.0 (2003-05)]
capacité de connexion assignée
section du ou des plus gros conducteurs rigides à raccorder, déclarée par le constructeur du dispositif de connexion. Dans le cas d'un dispositif de connexion pour conducteurs flexibles uniquement, la capacité de connexion assignée est la section du plus gros conducteur flexible à raccorder
[IEC 60998-1, ed. 2.0 (2002-12)]Тематики
- вывод, зажим электрический
- изделие электроустановочное
- клемма электротехническая
EN
FR
Франко-русский словарь нормативно-технической терминологии > capacité de connexion assignée
-
16 capacité de raccordement
номинальная способность к присоединению
Диапазон и/или число номинальных сечений проводников, на которое рассчитана клемма
[ ГОСТ Р 50030.7.1-2000]EN
rated connecting capacity
range of cross-sections and, if applicable, the number of connectable conductors, for which the terminal block is designed
[IEC 60947-7-1, ed. 3.0 (2009-04)]
rated connecting capacity
cross-sectional area of the largest conductor(s) to be connected as stated by the manufacturer of the installation couple
[IEC 61535, ed. 1.0 (2009-02)]
rated connecting capacity
cross-sectional area of the largest conductors as declared by the manufacturer
[IEC 60670-22, ed. 1.0 (2003-05)]
rated connecting capacity
cross-sectional area of the largest rigid conductor(s) to be connected as stated by the manufacturer of the connecting device. In the case of a connecting device for flexible conductors only, the rated connecting capacity is the cross-sectional area of the largest flexible conductor to be connected
[IEC 60998-1, ed. 2.0 (2002-12)]FR
capacité assignée de raccordement
gamme de sections et, le cas échéant, nombre de conducteurs raccordables, pour lesquels le bloc de jonction est conçu
[IEC 60947-7-1, ed. 3.0 (2009-04)]
capacité assignée de connexion
section du ou des plus grands conducteurs susceptibles d’être connectés comme indiqué par le fabricant du coupleur d’installation
[IEC 61535, ed. 1.0 (2009-02)]
capacité assignée de connexion
section du ou des plus gros conducteurs déclarée par le constructeur
[IEC 60670-22, ed. 1.0 (2003-05)]
capacité de connexion assignée
section du ou des plus gros conducteurs rigides à raccorder, déclarée par le constructeur du dispositif de connexion. Dans le cas d'un dispositif de connexion pour conducteurs flexibles uniquement, la capacité de connexion assignée est la section du plus gros conducteur flexible à raccorder
[IEC 60998-1, ed. 2.0 (2002-12)]Тематики
- вывод, зажим электрический
- изделие электроустановочное
- клемма электротехническая
EN
FR
Франко-русский словарь нормативно-технической терминологии > capacité de raccordement
-
17 connection capacity
номинальная способность к присоединению
Диапазон и/или число номинальных сечений проводников, на которое рассчитана клемма
[ ГОСТ Р 50030.7.1-2000]EN
rated connecting capacity
range of cross-sections and, if applicable, the number of connectable conductors, for which the terminal block is designed
[IEC 60947-7-1, ed. 3.0 (2009-04)]
rated connecting capacity
cross-sectional area of the largest conductor(s) to be connected as stated by the manufacturer of the installation couple
[IEC 61535, ed. 1.0 (2009-02)]
rated connecting capacity
cross-sectional area of the largest conductors as declared by the manufacturer
[IEC 60670-22, ed. 1.0 (2003-05)]
rated connecting capacity
cross-sectional area of the largest rigid conductor(s) to be connected as stated by the manufacturer of the connecting device. In the case of a connecting device for flexible conductors only, the rated connecting capacity is the cross-sectional area of the largest flexible conductor to be connected
[IEC 60998-1, ed. 2.0 (2002-12)]FR
capacité assignée de raccordement
gamme de sections et, le cas échéant, nombre de conducteurs raccordables, pour lesquels le bloc de jonction est conçu
[IEC 60947-7-1, ed. 3.0 (2009-04)]
capacité assignée de connexion
section du ou des plus grands conducteurs susceptibles d’être connectés comme indiqué par le fabricant du coupleur d’installation
[IEC 61535, ed. 1.0 (2009-02)]
capacité assignée de connexion
section du ou des plus gros conducteurs déclarée par le constructeur
[IEC 60670-22, ed. 1.0 (2003-05)]
capacité de connexion assignée
section du ou des plus gros conducteurs rigides à raccorder, déclarée par le constructeur du dispositif de connexion. Dans le cas d'un dispositif de connexion pour conducteurs flexibles uniquement, la capacité de connexion assignée est la section du plus gros conducteur flexible à raccorder
[IEC 60998-1, ed. 2.0 (2002-12)]Тематики
- вывод, зажим электрический
- изделие электроустановочное
- клемма электротехническая
EN
FR
Франко-русский словарь нормативно-технической терминологии > connection capacity
-
18 connection capacity
номинальная способность к присоединению
Диапазон и/или число номинальных сечений проводников, на которое рассчитана клемма
[ ГОСТ Р 50030.7.1-2000]EN
rated connecting capacity
range of cross-sections and, if applicable, the number of connectable conductors, for which the terminal block is designed
[IEC 60947-7-1, ed. 3.0 (2009-04)]
rated connecting capacity
cross-sectional area of the largest conductor(s) to be connected as stated by the manufacturer of the installation couple
[IEC 61535, ed. 1.0 (2009-02)]
rated connecting capacity
cross-sectional area of the largest conductors as declared by the manufacturer
[IEC 60670-22, ed. 1.0 (2003-05)]
rated connecting capacity
cross-sectional area of the largest rigid conductor(s) to be connected as stated by the manufacturer of the connecting device. In the case of a connecting device for flexible conductors only, the rated connecting capacity is the cross-sectional area of the largest flexible conductor to be connected
[IEC 60998-1, ed. 2.0 (2002-12)]FR
capacité assignée de raccordement
gamme de sections et, le cas échéant, nombre de conducteurs raccordables, pour lesquels le bloc de jonction est conçu
[IEC 60947-7-1, ed. 3.0 (2009-04)]
capacité assignée de connexion
section du ou des plus grands conducteurs susceptibles d’être connectés comme indiqué par le fabricant du coupleur d’installation
[IEC 61535, ed. 1.0 (2009-02)]
capacité assignée de connexion
section du ou des plus gros conducteurs déclarée par le constructeur
[IEC 60670-22, ed. 1.0 (2003-05)]
capacité de connexion assignée
section du ou des plus gros conducteurs rigides à raccorder, déclarée par le constructeur du dispositif de connexion. Dans le cas d'un dispositif de connexion pour conducteurs flexibles uniquement, la capacité de connexion assignée est la section du plus gros conducteur flexible à raccorder
[IEC 60998-1, ed. 2.0 (2002-12)]Тематики
- вывод, зажим электрический
- изделие электроустановочное
- клемма электротехническая
EN
FR
Англо-русский словарь нормативно-технической терминологии > connection capacity
-
19 connection posibility
номинальная способность к присоединению
Диапазон и/или число номинальных сечений проводников, на которое рассчитана клемма
[ ГОСТ Р 50030.7.1-2000]EN
rated connecting capacity
range of cross-sections and, if applicable, the number of connectable conductors, for which the terminal block is designed
[IEC 60947-7-1, ed. 3.0 (2009-04)]
rated connecting capacity
cross-sectional area of the largest conductor(s) to be connected as stated by the manufacturer of the installation couple
[IEC 61535, ed. 1.0 (2009-02)]
rated connecting capacity
cross-sectional area of the largest conductors as declared by the manufacturer
[IEC 60670-22, ed. 1.0 (2003-05)]
rated connecting capacity
cross-sectional area of the largest rigid conductor(s) to be connected as stated by the manufacturer of the connecting device. In the case of a connecting device for flexible conductors only, the rated connecting capacity is the cross-sectional area of the largest flexible conductor to be connected
[IEC 60998-1, ed. 2.0 (2002-12)]FR
capacité assignée de raccordement
gamme de sections et, le cas échéant, nombre de conducteurs raccordables, pour lesquels le bloc de jonction est conçu
[IEC 60947-7-1, ed. 3.0 (2009-04)]
capacité assignée de connexion
section du ou des plus grands conducteurs susceptibles d’être connectés comme indiqué par le fabricant du coupleur d’installation
[IEC 61535, ed. 1.0 (2009-02)]
capacité assignée de connexion
section du ou des plus gros conducteurs déclarée par le constructeur
[IEC 60670-22, ed. 1.0 (2003-05)]
capacité de connexion assignée
section du ou des plus gros conducteurs rigides à raccorder, déclarée par le constructeur du dispositif de connexion. Dans le cas d'un dispositif de connexion pour conducteurs flexibles uniquement, la capacité de connexion assignée est la section du plus gros conducteur flexible à raccorder
[IEC 60998-1, ed. 2.0 (2002-12)]Тематики
- вывод, зажим электрический
- изделие электроустановочное
- клемма электротехническая
EN
FR
Англо-русский словарь нормативно-технической терминологии > connection posibility
-
20 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
См. также в других словарях:
Área Metropolitana de Cúcuta — Área metropolitana de Colombia Lema: Por la región lo damos todo!.[1] … Wikipedia Español
Área Metropolitana de Neiva — Área metropolitana de Colombia … Wikipedia Español
Conductor (transportation) — This article is about the railroad crew member. For other uses, see Conductor (disambiguation). An Amtrak train conductor A conductor is a member of a railway train s crew that is responsible for operational and safety duties that do not involve… … Wikipedia
Electrical conductor — Overhead conductors carry electric power from generating stations to customers. In physics and electrical engineering, a conductor is a material which contains movable electric charges. In metallic conductors such as copper or aluminum, the… … Wikipedia
Michael Stern (conductor) — Michael Stern (born 1959) is a noted American symphony conductor. Currently, he serves as the music director and lead conductor of the Kansas City Symphony in Kansas City, Missouri. He is also the founding music director of the IRIS Orchestra in… … Wikipedia
Polímero conductor — Saltar a navegación, búsqueda La melanina, un polímero conductor Los polímeros conductores, también llamados metales sintéticos, fueron descubiertos en 1974 y desde entonces han despertado gran interés y un rápido crecimiento en la electrónica de … Wikipedia Español
Charles Munch (conductor) — Charles Munch (French pronunciation: [ʃaʁl mynʃ]; born Charles Münch) (September 26, 1891 – November 6, 1968) was an Alsatian symphonic conductor and violinist. Noted for his mastery of the French orchestral repertoire, he is best known as… … Wikipedia
Metropolitan Area Youth Symphony — The Metropolitan Area Youth Symphony (MAYS) is a youth orchestra in the Orlando, Florida region founded in honor of conductor and cellist, Jonathan May. The MAYS is led by Artistic Directors Maureen May and Michael Miller and features four… … Wikipedia
Michael Morgan (conductor) — For other people named Michael Morgan, see Michael Morgan (disambiguation). Michael Morgan (born September 1957 in Washington, D.C.) is an American conductor. He is currently music director of the Oakland East Bay Symphony and the Sacramento… … Wikipedia
Kiski Area School District — Kiski Area School DistrictDistrict typePublicReligious affiliationNoneLocationVandergrift, Pennsylvania, USAEnrollment 2006 2007Approx. 4,800 studentsGradesK 12District locationruralDistrict MascotCavalierDistrict colorsGold, White … Wikipedia
Railway electrification in Great Britain - conductor rail systems — Railway electrification in Great Britain Conductor Rail describes the different third and fourth rail systems used and their history.HistoryRailway electrification as a means of traction emerged at the end of the nineteenth century. It offered… … Wikipedia